Tile and Grout Cleaning

Guide · Homeowners · 3 min read · Updated 17 November 2026

How to Clean Grout Between Tiles (and What Not to Use)

Short answer

To clean grout, vacuum or sweep loose dirt, apply a dedicated alkaline grout cleaner or a mild detergent, leave it to work for several minutes, then scrub along each joint with a stiff nylon brush and rinse with clean water. Remove the dirty water rather than leaving it to dry. Avoid wire brushes, undiluted bleach on coloured grout and acidic cleaners on natural stone. Seal grout once it is clean and dry.

How to Clean Grout Between Tiles (and What Not to Use)

Why grout gets dirty

Most grout is cement-based and porous. Every time a floor is mopped, some dirty water soaks into the joints, carrying grease and fine soil with it. Because grout sits slightly below the tile surface, a mop glides over it without lifting what has collected there. Over months and years, light grey or white grout turns dark grey or even black.

In bathrooms and showers, the problem is different. Soap scum and body oils build up on the grout, and constant moisture lets mould grow, especially on joints near the floor and corners. Hard water adds limescale on top. Understanding which of these you are dealing with tells you which product will work.

Kitchens add a third factor: cooking grease. Fine droplets of oil settle on floor tiles near the hob and oven, then attract dust and soil, creating a sticky film that ordinary detergents struggle to cut. This is where an alkaline cleaner earns its place, because it breaks down grease rather than simply spreading it around. Hallways suffer most from grit and mud carried in on shoes, which grinds into the joints.

What you will need

You do not need expensive equipment to make a real difference, but you do need the right products for your tiles. Always check the tile type before starting, because a product that is safe on glazed ceramic can permanently mark polished marble or limestone.

A narrow, stiff nylon grout brush is far more effective than a sponge or scourer. For larger floors, a long-handled deck scrubber saves your knees and back.

  • Stiff nylon grout brush and a long-handled scrubbing brush
  • Alkaline grout or tile cleaner suited to your tile type
  • Two buckets: one for cleaner, one for rinse water
  • Microfibre cloths or a wet vacuum to lift dirty water
  • Rubber gloves and eye protection
  • Impregnating grout sealer for afterwards

Step-by-step method for floors

Start by vacuuming thoroughly, paying attention to the grout lines, because loose grit turns into an abrasive paste once wet. Dilute your alkaline cleaner as the manufacturer recommends and apply it to a section of around one or two square metres. Leave it to dwell for the time stated on the label, typically five to ten minutes, without letting it dry out.

Scrub each grout line in short, firm strokes along the joint, then work across the tiles. You should see the dirty water turn grey or brown. This is the crucial part: remove that dirty water with a wet vacuum, a squeegee or clean cloths, rather than leaving it to dry back into the grout. Rinse with clean water and remove it again.

Move on to the next section and repeat. On badly soiled floors, a second pass is common. Let the floor dry fully, ideally overnight, before deciding whether to seal.

Showers and wall tiles

For shower walls, start with a descaler suited to your tiles to remove limescale and soap scum, then use a mould treatment on stained grout and silicone. Work from the top down and rinse thoroughly. On grout that has been darkened by mould for years, some staining may remain even after cleaning, because the mould has grown into the grout itself.

Silicone sealant around the tray or bath is a different material. If black mould has penetrated the bead, it will not clean out, and the best fix is to strip it and apply a new bead of sanitary-grade silicone.

Products and methods to avoid

Many common cleaning shortcuts damage grout or tiles. The table shows the most frequent mistakes and safer alternatives.

AvoidWhyUse instead
Wire brushesScratch tiles and erode groutStiff nylon grout brush
Acidic cleaners on stoneEtch limestone, marble and travertinepH-neutral stone cleaner
Undiluted bleach on coloured groutCan lighten colour unevenlyMould treatment suited to grout
Mixing bleach with acidsReleases harmful gasOne product at a time, rinse between
Steam on old or cracked groutCan loosen weak jointsGentle hand scrubbing
Leaving dirty water to dryPulls soil back into groutWet vacuum or rinse and lift

Keeping grout clean afterwards

Once grout is clean and fully dry, apply an impregnating sealer to slow future staining. It soaks into the grout rather than sitting on top, so it does not change the look or make the floor slippery. Reapply every year or two in kitchens and hallways, or as the manufacturer advises.

For everyday cleaning, use a pH-neutral floor cleaner, change mop water often, and use a flat microfibre mop rather than a string mop, which tends to spread dirt. In showers, a quick squeegee after use cuts limescale and mould considerably.

When to call a professional

If grout is still dark after two careful passes, or you are dealing with natural stone, Victorian tiles or a large floor, a specialist clean is often quicker and safer. Professional rotary machines and extraction remove far more soil than hand scrubbing. Ceramic and porcelain floors typically cost £4–£8 per m² and a shower enclosure £90–£160.

A specialist can also tell you whether the grout is worth saving. If joints are cracked, hollow or crumbling, regrouting may be needed, and no amount of scrubbing will fix it.

Questions people also ask

What is the best thing to clean grout with?

For most ceramic and porcelain tiles, a dedicated alkaline grout cleaner and a stiff nylon brush work best. Leave the cleaner to dwell, scrub along each joint, then remove the dirty water rather than letting it dry. On natural stone, use a pH-neutral stone cleaner instead, because acids can etch the surface.

Can I use bleach on grout?

Diluted bleach can help with mould on white grout, but it can lighten coloured grout unevenly and it does not remove grease or soil. Never mix bleach with acidic or ammonia-based cleaners, because this can release harmful gas. A mould treatment designed for grout is usually a safer choice.

Why does my grout go dark again after mopping?

Mopping often pushes dirty water into the grout lines, where it dries and leaves soil behind. String mops and dirty mop water make it worse. Use a flat microfibre mop, change the water often, and seal the grout after a deep clean so it absorbs less dirt.

Written and checked by the Tile and Grout Cleaning team. Read our editorial policy.

Get a free tile and grout cleaning quote

Tell us what you need and we'll come back with a clear price.

Request a quote